Crevalle 26 Bay

Hull and Deck

• No wood construction
• Coal tar epoxy coated fuel tanks
• Single Piece Fiberglass Stringer System with foam flotation
• 10 Year Transferable Hull Warranty
• Black rub rail with Stainless Steel Insert
• Composite Transom
• Dedicated Anchor Locker
• Position Control Hinges on all Hatches
• Fiberglass Hatches Finished on both sides
• NMMA Certified using ABYC Standards
• Self Bailing cockpit
• Forged Stainless Steel thru hulls with duckbill valves
• Standard 6” Engine Jack Plate combined with notched transom allows our boats to leap on plane in shallow water with no propeller cavitation.  The notch provides so much water to the engine pickup that the engine can be run all the way up on the jack plate without fear of overheating the engine.
• Marelon Seacocks (Composite material, no corrosion or electrolysis)
• Anti-Venturi thru-hull fittings (Allows pumps to operate at speed)
• Hidden deck drains with stainless covers and duckbill valves
• Welded one piece stern eyes
• Deep cockpit for a safe dry ride
• Yacht Grip, non-skid deck
• Setback transom provides full aft deck
• Vertical rod holders on side of helm
• Under gunwale rod storage for (2) 8′ rods each side
• Forward rod lockers with room for (5) 7′-6″ rods on each side
• 40″ wide flip up aft seat
• Bow Dry storage
• (2) removable 72 quart coolers
• (6) Custom Crevalle pull-up cleats
• (8) Stainless cup holders 6 are LED illuminated
• Port and Starboard in-gunwale safety gear storage
• 12″ Standard Multifunction display
• Floor storage for 5 Gallon Bucket
• Custom aluminum Leaning post with backrest, rigging tray, (4) rod holders, and (2) stainless cup holders, and storage bin
• Unobstructed aft fishing deck
• Pre wired 8 AWG wiring for trolling motor
• Trolling motor plug panel with trim switch
• Custom flat bar grab rails molded into the deck
• Attwood 1100gph automatic/manual bilge pump
• Fuel Water separator
• Wet Sounds Speakers
• Trim Tabs -Lenco with LED indicators

Release Wells (2)

• Insulated 28 Gallon aft release wells
• Venturi aeration bubbler
• Dual jets
• Protected overflow stand pipe
• Commercial Aquarium type aeration
• Blue gel coat
• Attwood 800 gph, dual port aeration pumps
• LED lighting
• Check valves on intake plumbing to prevent water level from dropping while at speed.

Bait Well (1)

• Adjustable aeration jet can be closed to convert bait well into fully insulated cooler
• Wide opening allows easy access for cast nets
• Side mounted overflow fitting with removable filter dome means no stand pipe to get in the way of netting bait
• Blue gel coat
• Sealed lid with double gasket prevents slosh at high speeds and during turns

Helm

• Storm Cloud Grey gelcoat face to eliminate secondary glare
• Simrad GPS Multifunction Display and glove box
• Deluxe stainless steering wheel with power knob
• Integrated, LED lit, dual height, nonskid foot rests
• Welded 316 stainless steel console grab rail
• Compass (except tower boats)
• Dual Note Stainless Horn
• Engine data on multifunction display (No gauges)
• Portside helm door
• Backlit switch lables
• Dual illuminated stainless cup holders
• Console door with trash bag holder
• Individual circuit breakers
• LED lighting inside storage and bilge
• Fusion Bluetooth ready stereo
• Integrated engine data on electronics options (when ordered)
• Sea Star solutions hydraulic steering with tilt helm
• Console Rod holders with hook/knife/plier holders (Non-Hard Top boats)
• Helm panel with ring lit switches and backlit function labels

Technical Standards

• Tinned copper wiring with functions printed every 12″ on every wire
• LED cockpit lighting throughout, blue or white selectable
• Deutsch plugs on harnesses
• Sealed Bussbars
• Heat shrink electrical terminals
• Circuit breakers (not fuses)
• 8 AWG trolling motor harness
• Remote trim switch at bow
• No visible fasteners on panels
• Helm mounted dual battery switch
• LED Navigation lights
• Deluxe battery hold down trays

Upholstery

• Custom upholstery with contoured seating and cushions
• Contrasting color accents, top stitching, heat reflective vinyls and multi density foam provide maximum endurance and comfort
• Contoured forward helm seating and leaning post cushions
• Our Crevalle exclusive forward cushion package features easily removable molded backrests with integrated armrests.  No unsightly stainless pipes or hardware are used.
• All vinyls feature Syntec NBT (Nano-Block Technology) antimicrobial formulas to minimise “pinking” and limit mildew growth found in most lower quality vinyls

Disclaimer

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.